P0335 on a Nissan means the engine computer is not getting a correct signal from the crankshaft position sensor, which Nissan calls “CKP SEN/CIRCUIT.” Common causes are a wiring or connector fault, a failed sensor, a damaged signal plate or low battery voltage. Take it seriously: Nissan safety recalls for faulty crankshaft sensors warn that the engine can stop running without warning while driving. Check your VIN for open recalls first.
Facts cross-checked against Nissan safety recalls on NHTSA, Nissan service manual procedures and published repair estimates. See our sourcing policy.
This guide explains what the crankshaft sensor does, exactly when Nissan’s engine computer sets P0335, the causes in the order to check them, the Nissan recalls for Sentra, Altima, Maxima and other models, repair costs by model, and whether it is safe to drive. Recall details come from NHTSA records and the diagnostic steps from Nissan service manual procedures.
If your scanner also shows a camshaft sensor code, read our P0340 Nissan guide. For another common Nissan code, see our P1148 Nissan guide. And our free VIN decoder confirms your exact model, engine and build date.
| Code | P0335 (Nissan: CKP SEN/CIRCUIT) |
| Meaning | Crankshaft position sensor “A” circuit: missing or abnormal signal |
| Symptoms | Check engine light, cranks but will not start, stalling, reduced power |
| Common causes | Wiring or connector, sensor power supply circuit, failed sensor, damaged signal plate, low battery voltage |
| Safe to drive? | Not advisable: some Nissan crank sensor faults can stall the engine while driving |
| First step | Check for open Nissan recalls by VIN |
What Does P0335 Mean on a Nissan?
P0335 Code – Quick Diagnostic Intelligence
The crankshaft position sensor, which Nissan calls the POS sensor, tells the engine computer how fast the crankshaft is turning and where each piston is. The computer uses it to time fuel injection and spark. Without a good signal, the engine may not start or may shut off. Nissan’s service manual lists P0335 as “CKP SEN/CIRCUIT (Crankshaft position sensor “A” circuit).”
When the Engine Computer Sets P0335
According to Nissan’s service manual, P0335 sets when:
- “The crankshaft position sensor (POS) signal is not detected by the ECM during the first few seconds of engine cranking.”
- “The proper pulse signal from the crankshaft position sensor (POS) is not sent to ECM while the engine is running.”
- “The crankshaft position sensor (POS) signal is not in the normal pattern during engine running.”
Nissan’s confirmation test is run with battery voltage above 10.5 volts and the ignition on, which is why a weak battery can make the diagnosis misleading.
P0335 Symptoms on a Nissan
- Check engine light (Service Engine Soon) with P0335 stored.
- Cranks but will not start, because the computer has no crank signal to time spark and fuel.
- Stalling or reduced power. Nissan recall 01V-357 describes an engine that may stop, with the Service Engine Soon light on and reduced power.
- Hard starting or stalling when hot, which owners commonly report with a failing crank sensor.
Common Causes of P0335 (Check in This Order)
Low Battery Voltage
Nissan’s test procedure needs more than 10.5 volts with the ignition on. Test the battery and charging system first, because low cranking voltage can make other readings unreliable and it costs nothing to check.
Wiring or Connector Fault
Nissan lists “harness or connectors” first, meaning an open or short in the crankshaft position sensor circuit. Its diagnosis checks the sensor power supply, then the ground circuit, then the signal wire to the engine computer. Look for a loose connector, bent pins, corrosion or a chafed wire.
Sensor Power Supply Circuit
Nissan names “sensor power supply 2 circuit” as a possible cause. This circuit also feeds other sensors, so a short elsewhere on it can take the crank sensor down too. Check it before replacing the sensor.
Failed Crankshaft Position Sensor
If power, ground and signal wiring test good, the sensor itself is the likely fault. Use the correct part: owners and a Nissan bulletin discussed on enthusiast forums describe crank and cam sensors that look alike and can be mixed up, and some owners report that cheap aftermarket sensors did not fix the code.
Damaged Signal Plate
The sensor reads teeth on a signal plate that turns with the crankshaft. Nissan lists the signal plate as a possible cause and checks it last in its procedure. A damaged plate usually means a bigger repair.
Engine Computer Software
On some Altima and Sentra 2.5L models, Nissan’s fix for crank signal dropouts was a free engine computer reprogram under recall, described below.
Nissan Recalls for P0335 and Crank Sensor Problems
Several Nissan safety recalls covered crankshaft sensor problems that could stall the engine. Safety recall repairs are free. We found no Nissan service bulletin on NHTSA that names P0335 for the Frontier, Titan, Versa or Rogue.
| Recall | Vehicles | What it covers |
|---|---|---|
| 01V-357 | 2000 to 2001 Sentra 1.8L | Defective crankshaft sensor; the engine may stop. Replace the sensor |
| 03V-455 (Nissan R3022, Infiniti R3021) | 2000 to 2003 Sentra, 2002 to 2003 Altima and Maxima, 2003 350Z and Murano, plus several 2002 to 2003 Infiniti models | Heat stress on the crank or cam sensor circuit board solder joint. Replace the sensors |
| 06V-242 (Nissan R0606) | 2003 to 2004 Altima and Sentra 2.5L, about 294,000 vehicles | Brief crank sensor signal interruption with temperature changes; the engine may stop at low speed. Free engine computer reprogram |
| 07V-527 | 2002, 2005 and 2006 Altima and Sentra 2.5L | Crank sensor overheating causes a brief signal interruption. Free engine computer reprogram |
NHTSA’s VIN lookup does not show safety recalls that are more than 15 years old. If you own a 2000 to 2007 Nissan, call Nissan Consumer Affairs at 1-800-647-7261 to ask whether a recall is still open on your VIN.
How Much Does It Cost to Fix P0335?
These are RepairPal estimates checked in September 2026, before taxes and fees. A recall repair is free.
| Repair | Typical cost | Source |
|---|---|---|
| Check engine light diagnosis | About $125 to $183 | RepairPal national estimate |
| Crankshaft position sensor, Frontier | About $136 to $262 | RepairPal |
| Crankshaft position sensor, Pathfinder | About $155 to $271 | RepairPal |
| Crankshaft position sensor, Maxima | About $157 to $263 | RepairPal |
| Crankshaft position sensor, Rogue | About $172 to $268 | RepairPal |
| Crankshaft position sensor, Sentra | About $189 to $258 | RepairPal |
| Crankshaft position sensor, Versa | About $201 to $266 | RepairPal |
How to Diagnose P0335 Yourself
This order follows Nissan’s service manual procedure. Use your factory service information for exact test values.
- Check the battery. Nissan’s test needs more than 10.5 volts with the ignition on.
- Check open recalls by VIN, or call Nissan for older vehicles.
- Inspect the sensor connector and harness for bent pins, corrosion and damage.
- Check the sensor power supply, ground and signal wire to the engine computer.
- Replace the sensor with the correct part number, ideally an original-equipment part.
- Inspect the signal plate if the code returns with a good sensor and wiring.
- Ask a dealer about software updates or an engine computer check as the last step.
Can You Drive With a P0335 Code?
It is not a good idea. Nissan recall 06V-242 warns that a crank sensor signal problem means “the engine may stop running without warning while the vehicle is driven at a low speed increasing the risk of a crash.” Even if your car still runs, the fault can get worse. Avoid highway driving and heavy traffic until it is fixed, and have it towed if the engine stalls or will not restart.
P0335 vs Related Nissan Codes
- P0340: camshaft position sensor (PHASE) circuit. P0335 and P0340 together often point to shared wiring or a power supply problem.
- P0345: camshaft position sensor “A” circuit, bank 2, on V6 engines.
- P0336: crankshaft position sensor range or performance: the signal is present but erratic.
- P0339: crankshaft position sensor circuit intermittent.
The Bottom Line
P0335 on a Nissan points to the crankshaft sensor signal, and it can make the engine stall. Check your VIN for recalls, test the battery and wiring before buying parts, use the correct sensor, and do not keep driving a car that stalls.
Frequently Asked Questions About the P0335 Code on Nissan
What does P0335 mean on a Nissan?
Can a bad crankshaft sensor cause a no start on a Nissan?
Why does P0335 come back after replacing the crank sensor?
Is there a Nissan recall for the crankshaft position sensor?
How much does it cost to replace a crank sensor on a Nissan?
Should I replace the crank and cam sensors together?
Related guides: trouble code guides by make and P0420 Code Explained: Causes, Fixes, and 2026 Repair Costs.
⚠️ Professional Notice:
Recall eligibility depends on your exact VIN. This guide is general information; a Nissan dealer has the final word on coverage and repairs.
Cost figures are published estimates and vary by vehicle, region and shop. Always get a written quote before authorizing a repair. NextCarReview.com does not receive compensation from any parts manufacturer, retailer, dealer or repair chain for editorial coverage.
Data Sources and Verification
- Nissan service manual, P0335 CKP sensor (POS) diagnosis: Rogue, Sentra
- NHTSA recall 01V-357: nhtsa.gov
- NHTSA recall 03V-455: nhtsa.gov
- NHTSA recall 06V-242 (Nissan R0606) owner letter: static.nhtsa.gov (PDF)
- NHTSA recall 07V-527: nhtsa.gov
- RepairPal repair estimates: Frontier crankshaft position sensor, Sentra crankshaft position sensor, check engine light diagnosis
- NHTSA recall lookup: nhtsa.gov/recalls
Morgan Reyes is the Lead Automotive Journalist and EV Analyst at Next Car Review. Specializing in mechanical systems and next-generation electric vehicles, Morgan breaks down complex automotive data, legacy matchups, and upcoming model previews into practical insights for car buyers.
